Portsmouth Auto Locksmith

Ignition Barrel Repairs in Portsmouth

A key that will not turn, turns part way, or turns and does nothing. The barrel is repaired or replaced at your vehicle, with a key cut to match it in the same visit.

Portsmouth and nearby townsOpen 9am to 5pm, seven daysNo VAT added
Repaired at your vehicleKey cut to matchDiagnosed before you buy a key
Priced on callBarrel repair
Same visitKey cut to match
No VATOn any figure

Between 9am and 5pm. Describe what the key does and most of this can be narrowed down on the phone.

Tell me about the vehicle

Make, model, year, the registration, and what the key or the car is doing. I will come back with a price.

Before you buy another key

A key that will not turn is the one fault people most often spend money on twice. They buy a new key, the new key does exactly the same thing, and the barrel was the problem all along.

The barrel is the lock the key turns in. Inside it are spring loaded wafers that the cuts on your key lift to exactly the right height. Years of use wear both the key and the wafers, and the two wear together until one day the alignment is no longer close enough.

Which half has worn decides the fix. A fresh key cut to the vehicle pattern often cures it outright. A barrel that is already damaged needs the barrel.

Telling them apart

  • A spare key turns normally: your main key is worn, not the barrel.
  • Both keys feel the same: the barrel is the likelier half.
  • It got worse gradually over months: wear, in one or the other.
  • It failed suddenly after a knock or a theft attempt: the barrel.
  • It only sticks when cold or damp: usually the barrel.

The three faults behind the same symptom

They feel similar at the wheel and they cost very different amounts to put right.

What you feelLikely causeWhat it needs
Key goes in, will not turn at allWorn key or worn wafersA fresh key first, then the barrel
Turns part way then stopsSteering lock engagedRock the wheel while turning the key
Turns freely, nothing happensBarrel detached from the switchBarrel or ignition switch
Turns, dash lights, no startNot the barrel at allChip or immobiliser
Mercedes, wheel stays lockedElectronic steering lockESL or EIS work
Key snapped off in the barrelMechanicalExtraction then a new key

Try this before you ring

Two of the commonest call-outs for a key that will not turn are not faults at all, and both take ten seconds to rule out.

The first is the steering lock. If the wheel was turned against its stop when you parked, the lock pin is under load and the key cannot move. Rock the steering wheel gently left and right while turning the key, with no force on either. It frees almost every time.

The second is the gear selector. Many automatics will not release the ignition unless the selector is fully home in Park. Nudge it firmly into Park and try again.

What not to do

  • Do not force the key. A snapped key in a barrel turns a cheap job into two jobs.
  • Do not use pliers for leverage. They twist the blade and ruin the cuts.
  • Do not spray oil or lubricant into the barrel. It collects grit and accelerates the wear you are trying to fix.
  • Do not keep trying once it is clearly stuck. Each attempt wears it further.

Where I cover

All of Portsmouth at one price, including Southsea, Fratton, North End, Cosham, Hilsea, Landport, Buckland, Milton, Eastney and Portsea.

North of the city I cover Cowplain, Purbrook, Widley, Horndean and Clanfield. If the car cannot be started it does not need to move, because the work is done where it is parked.

Towns with their own page

Each one says what I do there.

Frequently asked questions

My key will not turn in the ignition. What do I try first?

Rock the steering wheel gently while turning the key, and check an automatic is fully in Park. Between them those two account for a large share of the calls I get for this.

Will a new key fix a sticking ignition?

Often yes, if the key is the worn half. A key cut fresh to the vehicle pattern rather than copied from your old one restores the alignment the barrel expects.

Can you replace the barrel without changing all my locks?

Usually. Where a new barrel cannot be matched to your existing key, a key is cut to the new barrel in the same visit so you are not left with two keys.

The key turns but the car does nothing at all. Is that the barrel?

If the dashboard does not light up, it can be the ignition switch behind the barrel. If it lights up and the engine will not run, that is the immobiliser rather than anything mechanical.

Is this covered on a van?

Yes. Van barrels wear faster because of the number of turns a working vehicle does in a week, and they are done at the kerb the same way.

My key snapped while I was forcing it. What now?

Leave it where it is and ring. The broken piece is extracted and a replacement cut, both in the same visit. Do not try to grip the stub.
Scroll to Top